Sheet S-03 · WISECUT tube machines
WT-12035T 20kW Pipe Laser Cutter with Four Chucks
The WT-12035T is a four-chuck, super heavy-duty tube fiber laser cutting machine for tubes up to 12 m long, offered from 3 to 20 kW.
- Machine
- WT-12035T
- Type
- Four chuck super heavy-duty
- Chucks
- 4
- Max tube length
- 12 m
- Power
- 3–20 kW
- Sheet
- S-03
APlate and tube length
Tube length drawn to scale. Chuck positions are schematic.
BOverview
The WT-12035T is a four-chuck, super heavy-duty pipe laser cutting machine for tubes up to 12 m long, offered from 3 to 20 kW. It carries the most chucks and the widest power range of the WISECUT tube machines.
There isn't much more to state about it, and we'd rather say so than pad the page. Four chucks, a 12 m maximum tube length and a power range that reaches 20 kW are what we can stand behind. The clamping range, the machine footprint and the cutting capacity are confirmed in the quotation for the configuration you order. Our figures for this model also overlap with a sister model's in ways we can't verify, which is one more reason not to print them.
Think about power before you think about the badge. A 20 kW source costs more to buy and to run than a 6 kW one, and it only earns that back on tube that needs it. Bring us your heaviest wall and your usual wall. If most of your work sits at the lower end, the WT-6035T may serve you better. It has the same 12 m length, three chucks, and a stated bevel and loading feature set, so compare the two pages side by side before you decide.
CDatasheet
Stated rows come from our product information. Open rows are confirmed in the quotation.
| Parameter | Value | Status |
|---|---|---|
| Chucks | 4 | Stated Four chucks for the heaviest loads in the range. |
| Power range | 3,000–20,000 W | Stated The highest power range among the tube machines. |
| Maximum tube length | 12 m | Stated Nominal value from our website. |
| Tube section and clamping range | — | In the quote Confirmed per machine, against your section drawing. |
| Wall thickness and cutting speed | — | In the quote Not printed here. They depend on material, power and configuration. |
C2Website parameter table
Template values from our website; they will be replaced by the official model table.
| Parameter | Value |
|---|---|
| Processing range | Round and square tube Φ10–Φ500 mm |
| Cutting length | 12000 mm |
| X / Y / Z axis | 1000 / 12000 / 300 mm |
| X/Y positioning accuracy | ±0.03 mm / 1000 mm |
| X/Y repeat positioning accuracy | ±0.02 mm / 1000 mm |
| Z positioning accuracy | ±0.02 mm |
| X/Y maximum positioning speed | 90 m/min |
| Chuck rotation speed | 105 rpm |
| Power supply | 3 phase, 380 V, 50 Hz, IP54 |
| Machine power (without laser and chiller) | 27 kW |
| Overall dimensions | 29500 × 3150 × 2290 mm |
| Machine weight | 21.5 T |
| Laser in table configuration | Raycus 6000 W |
Parameters from the WISECUT website parameter table (template values; to be replaced by the official model table). Final specification is confirmed in the quotation.
DFeatures
- Four chucks, for the heaviest tube and profile loads in the range.
- Offered from 3 kW to 20 kW, the widest power range among the tube machines.
- Maximum tube length 12 m.
EWhere it is used
- Heavy tube and profile at lengths up to 12 m, where more support points along the tube help keep it steady.
- Buyers who know they need power above 12 kW on tube. Only this model is offered up to 20 kW.
- Shops planning the line around one large tube machine and willing to size the building and the supply for it.
- A caution from an independent guide, worth keeping in view: it says higher power is not always the right call, because excessive laser power increases machine cost, energy consumption and maintenance expenses. Choose by your common material and thickness. See Bodor's tube cutter guide.
FOpen until the quote
Send the tube you cut and we confirm these items for this machine in the quotation:
- Tube section and clamping range. Website template values are listed in the parameter table; the quotation confirms the range against your section drawing.
- Wall thickness and cutting speed. Depend on material, power and configuration; confirmed in the quotation.
- Laser source, controller and cutting head. Fixed in the quotation for the configuration you order.
- Machine footprint and weight. Website template values are listed in the parameter table; the installation drawing comes with the quotation.
GFAQ
Why does this page state so few figures?
Because we only print what we can support. The figures we hold for this model are not reliable enough to publish, so the quotation states them for the configuration you order, against your tube.
Does the WT-12035T bevel or load semi-automatically?
This page doesn't state either for the model. The WT-6035T is the machine with stated bevel cutting and semi-automatic loading; see its page.
Do I need 20 kW?
Only if your tube needs it. Tell us the material and the thickest wall you cut regularly. The price page shows how power enters the quotation.
Can I test my tube before I order?
Yes. Free proofing is available on request. Read the sample service page for what to send, and include the longest length you cut.
How is four chucks different from three?
More support points along a long, heavy tube. The chuck configuration page compares them.
HNeighbouring sheets
Send a tube for the WT-12035T
Tube type, section, wall thickness, length and material are enough to start. We reply with a suitable machine and a quotation.